Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
Were you in search of information on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a bathtub isn't specifically brain surgery, but it does call for solid plumbing, carpentry, as well as in some cases, tiling skills. Replacing an old bath tub with a new one is also a reasonably hard project. If the old bathtub is readily available, the job can move quickly; if you need to open up a wall to get rid of the old bathtub as well as position the new bathtub, the task is much harder. In either situation, the job is within a residence handyman's skills, although you will require a helper to vacate the old tub and set in the brand-new one. See to it you have actually qualified yourself for the task and are comfortable trying it. Rather than employing a service provider to take control of a halfway-completed job, it is much better to think about utilizing one before you start. Possibilities are you may need a professional plumber to make tube connections.
This write-up will certainly aid you install a brand-new bath tub in your shower room if you have actually currently bought a new bathtub and don't need to alter the setup of your previous water supply pipelines.
Your devices and material list must consist of the following:
Planning for the Installment
To start with, the sustaining framework supplied with the bathroom should be fitted (if needed) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to make sure that if the faucet includes a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is additionally reasonable to fit a supporting plate under the faucets system to prevent pressure on the bathtub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you utilize every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath must now be ready to be fitted in its last position.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you must do is separate the supply of water. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing taps can be quite troublesome as a result of the limited gain access to that is typically the case.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric ready for the staying water that will certainly come from the pipes. As soon as the supply pipelines have actually been removed, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this procedure. When the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Prior to moving on to fit the brand-new taps, contrast the pipe links on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Installing the Bathtub
Using the two wooden boards under its feet, place the bathtub in the called for placement. The wooden boards are helpful in equally spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 tiny points.
The following goal is to make certain that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bath tub up until the spirit level checks out degree.
To set up faucets, fit the bottom of the outermost adaptable faucet port to the appropriate supply pipe by making a compression join; after that do the same for the various other faucet.
Activate the water and check all joints and new pipework for leaks and also tighten them if essential. Load the bath tub and likewise inspect the overflow electrical outlet as well as the normal outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's user's manual. Tiling and also sealing around the tub should wait till the bathtub has actually been made use of at the very least once as this will certainly resolve it right into its final setting.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to avoid damage to the thread. One end of the port fits on the plastic tail of the tap and the other end provides a connection to the current supply pipes.
If you need to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin guaranteeing that the washers remain in area between the tap as well as the sink. Secure the faucet in position with the manufacturer offered backnut. As soon as the faucet is firmly in place, the supply pipes can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet ports. The previous kind ought to be attached to the faucet finishes first, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to split an inflexible seal, triggering the water to permeate the wall between the bath and the tiling, resulting in complications with dampness and possible leaks to the ceiling below.
You can choose from a range of coloured sealers to assimilate your components as well as fittings. They are sold in tubes and cartridges, and also can securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly fill the bath tub with water prior to securing, to enable the movement experienced when the bathtub is in usage. The sealer can split fairly very early if you do not take into consideration this motion before sealing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently available on the market. It is a good idea to fit the floor tiles utilizing water-resistant or waterproof adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading about How to Install a Bathtub? Put feedback further down. We would be pleased to listen to your views about this review. We are looking forward to see you back again in the near future. Don't hesitate to take a moment to share this write-up if you enjoyed it. Thanks a bunch for your time. Come back soon.
Save your home, call now! Report this page